The Hub

This is an LP copy from Memphis guitars. It looks like it has had the headstock repaired at some point. Also, there is what looks like some separation of the fretboard near the nut. I don't know if its left over from the repair or if its something new and just trying to go this way. I'm asking the group to look at the pics to help me figure out if any corrective steps are needed. Also from a finish repair standpoint, how to deal with i…

I don't have a piece of mahogany that is wide enopugh to make the heel block on a dreadnaught guitar. Would black limba make a good heel block? I have a piece of black limbaquarter sawn and 5 inches wide.

Just posted a full build video for the last mandolin batch over on YouTube. Give it a watch folks, its 25 mins long. And there should be a few woodworking tips there for some of you, and some lovely tunes all played on my work.

Hey, I'm working on a 2017-ish Taylor GS Mini which has a delaminating headstock...see photos... I was surprised to see that the laminate was plastic... I reckon quite a few of the community will have done this job many times, so I'm after group wisdom :). Just a small request I know... Just Fyi...I haven't quoted the customer yet, but I reckon (with some other work I'm doing on the instrument)...our budget will be limited.…

Let me start with this; I'm trying to find the root cause of difficult fret wire installation of two different SM fret wires. I've spent a lot of time gathering dimensions and experimenting with techniques wich could cause the problem. I enlisted the help of a colleague who arrived at a similar poor performance. His solution was to glue the fret ends/ beat the frets in. My "rather" is to find the root cause so I don't have to go thr…

Have an electric archtop that has a .012" backbow strung with 12-48s with truss rod completely loosened. 3 piece maple neck with a Ziricote fingerboard... Any tips or recommendations to straighten this neck would be appreciated... Currently trying humidity (in the case). Thank you! David O'

Since most of us fix or make guitars, we have probably heard something about the cease and desist letters Fender has sent out concerning the Stratocaster. I thought I would offer some thoughts. As always, caveat emptor. There are three basic ways to protect intellectual property under Federal law. Patent, trademark, and copyright. Each protects different things, and has different underlying legal theories. Lets begin with pate…

Dialled in the Beta, much further. Now at v1.1.0 Echoing Christopher Alexander’s argument in the first half of “Notes on the Synthesis of Form” here. Parametric, Semi-Lattice Structures. Centres within Centres, interacting to form the whole. A living structure. Because of the dimension of time, and feature hierarchy, and methodology we end up with a Centre Oriented Semi-lattice Hyper-graph, or COSH for short. This will be available on the…

Straight Frets in Austin has an excellent full-time position opening up soon. The job pays by the job, and equates to $70-85K a year for a tech that does: *neck resets *structural repairs *bridge making/reglues *refrets *headstock breaks with splines/airbrush We work on about 1,350 guitars a year (about 28-30 a week) and have had work shipped in from 22 different states at this point. We also teach setup classes on…

All - looking for recommendations on overall approach for repairing this nasty side crack right at the edge of the tail block. My initial thought is that either the top or the back needs to come off in order to properly glue and clamp the main split. Thanks in advance. Images

I'm using hide glue on this 1st build. So far I've glued up the kerfing, back braces, and the top "X" brace. I'm using the 190 grade glue. Working time is short at best. I heated the top "X" brace surfaces (brace & top) with a blow dryer and that seemed to help, a little. How can I get enough working time to glue the top, and then later the back, without having to rush and creating a real mess in the process? Suggestions and reco…

I am working on a neck reset on a Washburn Parlor - SN 283552. I have read that the 28 in the SN indicates that is was built in 1928, but the owner thinks based on her research that it was built before 1920. I am assuming a dovetail joint and that I can get into the neck joint for steaming by drilling into the 13th fret slot, but if anyone knows differently please let me know. The fingerboard extension has already separated slightly…

Good morning everyone, it is been a while since I wanted to replace my glue (standard Titebond) with epoxy. The best I can find in EU, and specifically in Italy, is the West System 105 with 206 hardeners. Is it any good for fretboard and top gluing or neck gluing? For all the other small task, like top jointing etc I'll still use Titebond or polyurethane glue. Thanks!

Hi all, To those of you that work out of your house, how are you insuring your home/business? We are moving house and just had a homeowners policy cancelled due to my home business. Given how easy it is for these companies to deny claims, I want to make sure I do everything on the up and up. I'm in New York, and have Heritage for instruments that come in and out of my shop.

Rask Guitars — Utah (relocation required) Rask Guitars is a Utah-based custom shop dedicated to building exceptional instruments — primarily high-end acoustics, alongside electric guitars and prototypes. We operate with a small, focused team where craftsmanship isn't just a standard, it's the entire point. We're growing, and we're looking for a skilled, experienced luthier who's ready to plug into a real production environment, contribute…

An old friend of mine, Les Stansell, who has been building some pretty high-end guitars and ukuleles for over three decades has had to close his shop for health reasons and is looking to sell all his tools and equipment. I’m spreading the word to help him find a suitable buyer – hopefully a new luthier ready to set out on their own. If someone is interested they can contact me here and/or contact Les directly at [email withheld]…