The Hub

(Just to set expectations, I bought this for the sole purpose of learning. Not a client project) I got this Martin D28-12 in destroyed condition, after an airline did something awful. As I see it: - Top cracks - Back cracks - Top & side separation with some broken off kerfing - Brace ejected When I was looking at the pictures online pre-purchase, I thought I might take the neck off and re-top it, or at the very least, take the top off and fix…

Before I hack into the Yamaha, I would like to get the opinion of the experts on a method of steaming the upper end of the guitar and ‘pressing’ the neck down to adjust the angle back to factory. There are several you-tubers that have tried and recommend it. My novice intuition is that even though it may work, wont the steaming of other areas of the body such as upper braces, etc, end up weakening the construction (glue stability) to…

I watched the Guild F-20 video (https://dev2.loothgroup.com/groups/repair-and-restoration/forum/topic/cracker-x-braces-on-guild-f20/#post-60310) with great interest since I've been working on a Gibson L-3 with a similar problem. A little back story - The original repair request was to address a small pickguard crack on the sound hole side. After peeking inside, I saw 5 loose brace ends on the treble side. Still a pretty standard repair…

Hey all, I’m curious to know people’s general thoughts on the appropriate or ideal saddle height after a reset. And, when to replace a bridge that’s been shaved down. I know there are a lot of factors (for me anyhow) and this question could open a whole can of worms when it comes to the specifics of the guitar, its age, style of bridge and desired sound. I’m providing an example I encountered recently, but would also like to know people…

In the process of evaluating the repairs needed on this guitar I checked to see if the truss rod was working. There is hole in the transverse brace where you would normally insert a truss rod, but all I see is the end of a metal bar with a smallish hole in the center. I tried several allen wrenches that would fit in the hole, but nothing seems to grab. Did they really eliminate the adjustable truss rod on this vintage reproduction? Here'…

Initial frequency analysis of this D28 copy (done with a temporary 35g bolt-on bridge and the back plate taped on) is VERY LOW. Main air resonance 83.5hz and top monopole 156.6. It's standard Martin scalloped X-bracing with a torrefied Adirondack top. Since I can still easily access the bracing, I'm thinking of going in and laminating wood on top of the X brace to stiffen it. Other options would be a very light bridge, though I'm not…

Hello everybody! I've got a newer Martin Special 16 (all solid wood with matte back/sides and gloss top) in for some loose braces. Here in Houston I'm used to dealing with acoustics damaged by over-humidification or extreme heat rather than what I often see addressed in the group by you wonderful folks in your colder (normal) climates. My customer had this guitar shipped to him from Wisconsin, and I suspect it was exposed to some extreme…

A customer brought a Martin D28 in for an assessment and below is the main issues with the guitar. It has two loose braces and two warped/broken "stringers" along the back of the guitar. In addition, the guitar is a candidate for a neck reset, although I think I can possibly kick that can down the road, and my main concern is the loose braces. I'm wondering what the best way to repair something like this is? I don't have much experience…

So this 46' J-45 came to me at a very very low price as it needs extensive repair. Much that I am confident in, cracks, bridge/bridge plate issues, loose braces and the like. There are however a few points that id like the groups opinions on. The neck angle is pretty great and theres a good amount of fret, however, at some point in its past, someone shaved down the neck to a dangerous point, and the back of the neck has toms cracks along…

This is my mid 50's LG-1. I had the back off to replace the bridge plate and one of the braces. I've got it all back together now but I'm lacking the knowledge to make my work disappear. I was using amber CA glue to color the binding but that didn't seem like the proper route so now I'm scraping, filing and sanding that back off and starting over. I watched Doug Proper's demonstration on liquid binding repair and that did have a lot…