The Hub

Stew Mac Erlewine Neck Jig for sale, purchased new in May of 2023. Very light use in excellent condition. More photos upon request. Comes with angle vise, shipping based on location. Available for pickup in Fairfield County, CT. $550.00 Erlewine Neck Jig Workstation - StewMac

This video is just a quick example of how simple the Jaws 2 is for setting frets. We did not include shots of using glue to keep the fret down. This guitar was donated for teaching purposes…We will be pulling all the frets and performing a full refret in a later video

Good morning group! I just joined The Looth Group today. I'm wondering what folks are currently using to sharpen chisels, plane blades, violin maker's knives. Is there a jig you would suggest? What stones, or are you using something better, easier? I know sharpening is a whole world unto itself but I'm looking to up my game. Currently using Japanese water stones and an inexpensive one wheel guide. I'd like to do better. Thanks! Spidey

Just starting to research these items, so forgive the noob question/s… Can these two items be combined? I.e. could one fasten the Erlewine neck jig to the Proper workstation? Or are they two completely different items? Does the Proper workstation allow you to do fretwork under string tension, or is that only on the Erlewine jig? Or could you possibly buy both items, then switch them out on the same mounted post? My primary issue I’d like…

I just opened a repair shop and the first repair was to remove a broken 1/8" hex wrench ball end from the truss rod nut of a Turner RB4 Renaissance Bass. I read of all sorts of theories on how to extract/remove. None of them had recorded actual attempts of the theories. There's probably others on here but I haven't found them. The ball end was loose and mangled at the rear of the nut sleeve. I tried fairly benign methods first. Heat…

Hey Everyone! Does anyone have experience with using the neck jig/shop stand setup without bolting the stand to the floor? Eventually I will bolt it down but want to try a few different spots to commit (still working on shop layout). I just had epoxy floors put down and do not want to drill extra holes in the floor! Thanks!

Hello everyone, this will be a long post. I usually describe my passion for luthiery as a "fire." I can easily remember the day I realized that I wanted this to be what I would do for the rest of my life. It started as pure joy; learning day by day was like unwrapping a new surprise. I did everything right: studied, practiced, studied, practiced. I built my own jigs and tools, and I even did a small apprenticeship with a local luthier. Wh…

Hi everyone! I'm looking for advice about heat treatments for a warped neck, I know they are a thing but I've never actually done one. I have an Epiphone Les Paul in the shop that originally I was only going to do a level/crown/polish and a setup on, but when I tried to adjust the truss rod and checked the fingerboard with a straight edge I noticed there was about .030" of relief in most of the middle section, which was pretty consisten…

Hey everyone, I could use some advice as far as the fretting process is concerned. I’ve been doing guitar repair since around 2008, I opened my business doing guitar repair in September of 2021, and I’ve always felt that fretwork has been the most challenging part of this job. I’m getting to the point now where I finally feel like I’m getting the hang of it, but I’m not where I want to be yet. I should mention that I use the Erlewine…

Happy New year everyone!!! I have an LMII neck angle jig but only have the dove tail templates. Would like to try a bolt on for my next acoustic build. With LMII's unfortunate departure do you know where I can get the templates for the mortise and tenon? Is anyone making these? perhaps our friends fortunate enough to have a CNC? I tried making one for a ukelele build but with the tools I have, not confident in the accuracy. Any leads are…

Was using one of my favorite tools today and wondering what happens when LMI is gone? Is there a possibility someone takes over production of these great tools and jigs? When I heard about LMI closing, I immediately went and ordered a backup fret tang filer…a tool I use every week.

Hey all! First time posting around here, so forgive me if this has been talked through before, but I'm on the hunt for some jig plans for routing splines on headstock repairs. Thanks so much for any help or direction on this!

I'm working on a repair to a Washburn EA50 headstock. Someone previously tried to repair this with a dowel, which likely worked until it was strung up. I've routed a slot and created a biscuit, and built a jig to hold both parts of the headstock in the same plane and clamp everything tight (some cauls and threaded blocks of maple with 1/4-20 machine screws). The plan is to use System 3 gel epoxy (a'la Beau Hannum) and then add a coup…

Hello, I just went to the Northwoods seminar and came away with ,maybe it's time to get a CNC machine. So I'm curious which one do you have? Why did you purchase said machine? At this time I don't want to buy an entry level machine. I would prob start with making bridges, templates, jigs and other assorted small parts. Maybe necks at a later date. I would like a machine that I dot have to upgrade in one year. Would also prefer a spind…

I have a few acoustic steel string backs to reglue. Looking for jig ideas to assist in lining up the rib structure for this operation.