The Hub

I attach my necks using the LMII/O'Brien jig. No matter the method, there is no guarantee that the neck block and edge of the rim at the top is truly perpendicular to the centerline of the guitar. I’ve just flossed when things weren’t quite right. But now I take a long square, place it on the rim at the neck block and measure where the long square aligns on the top seam. I note Bass/Treble deviation at a known point (I use 290 mm).…

I have a red-label Yamaha FG-180 that’s in overall nice condition, but the neck angle is poor and the heel is already cracked. I’d like to attempt a neck reset, but I’m unsure how to proceed given the existing crack. Should I approach the reset as usual, or plan an alternate method because of the damage? Has anyone here tackled a reset on a guitar with a pre-existing heel crack? I know a crack can develop during the reset process, but I…

It was only a matter of time before one of these arrived on my bench. The neck on this 71 SG Deluxe is caving through to the neck pickup cavity— In a similar fashion to what happens on old jr’s. Both sides of the cutaway have cracks that extend through to the pickup route and I can flex them easily. Problem is that the cracks are not straight and wander all over. I worry about being able to get enough glue in there because of this. Thin…

I've been trying to figure out an easy to use jig that will allow me to clamp a top and back fast, so that I can use hot hide glue. No way with my spool clamp method I could ever get everything clamped in time. I thought about trying to use pneumatic cylinders with 3D printed perimeter feet, but that seemed very complicated and a lot of work to get something to attach the pneumatic cylinders to. But it kept coming back to me that usi…

In this video, I show an alternative way to remove humbucker covers with no soldering required. Check it out and enjoy!

Hey folks, I put together a video showing how I measure the long, cross, and transverse frequencies on guitar top plates before thicknessing, following the Gore method. I also walk through using the calculator I built (based on Trevor Gore’s equations) to get target thickness and track density / young's modulus. Fair warning: the video’s a bit YouTube-y in tone thumbnail faces, a little energy for the algorithm, but the content is genuine…

Wondering what methods people use for tracing the shape of a cavity to make new covers, backplates, or switch-plates? Attaching a photo example of a battery cavity that's missing a cover and wondering what the best way would be to trace and reference the size so I can transfer it to a cardboard cutout and eventually cut a piece of wood to cover the cavity?

What kind of pore filler do you use? I usually use aqua coat, shellac/pumice or stewmac water based mahogany grain filler. Interested in other methods, including zpoxy.

I rarely use pickguards on my builds, as most of my guitars are intended for fingerstyle players. That said, I occasionally need to install one, and I've yet to find a cutting method that consistently meets my quality standards. I’ve experimented with several techniques for cutting clear pickguard material, but the results are always somewhat disappointing. Using a brand new X-Acto blade gives a reasonably clean cut, but there's almost a…

Hello fellow looths ! I'm deciding on a repair method for the jack recessed/angled hole on this Aria Pro SB bass. What kind of direction would you take ?

Hello good people, My shop’s in Quebec City, so I get to repair an ungodly amount of cracks thanks to our brutal winter and customers being largely unaware of the requirements of maintaining proper RH. Now for the first time (call me lucky) I have two very good guitars in the shop whose cracks won't close up after having been rehumidified for a few weeks. I have tried over-humidifying and it does it, but once returned to proper RH (50%)…

Please can I see some quick cauls for dealing with fret pressing at heel transitions? For pressed / glued in frets or clamping down lifting fret ends in this area. I’ve tried a few different methods now and not entirely happy with any of them

I've been testing all my top and bracewood to find the best combination of stiffness and density, optimize plate thickness, etc. I started with Nicoletti's spreadsheet which calculates both stiffness and density, but since I was also testing deflection, I decided to compare the flexural modulus using that method (with the formula from T. Gore's book) on the same plates and bracewood. Unfortunately, I'm having trouble getting a satisfa…