The Hub

I watched the Guild F-20 video (https://dev2.loothgroup.com/groups/repair-and-restoration/forum/topic/cracker-x-braces-on-guild-f20/#post-60310) with great interest since I've been working on a Gibson L-3 with a similar problem. A little back story - The original repair request was to address a small pickguard crack on the sound hole side. After peeking inside, I saw 5 loose brace ends on the treble side. Still a pretty standard repair…

I got some chips due to pulling the frets. Does anyone have any tips for fixing this?

We install a lot of LR Baggs pickups, but nobody has ever gotten more excited about their new pickup than Andy Wood. If you don't know Andy, watch this fun video.

I've been building up my "2 car garage shop" for about 10 years preparing for retirement from health care. This spring I finally quit punching the time clock. Over the same time I've build 13 mandolins and 4 guitars. Now I pretty much have all my tools in place and enough wood stored to build for quite some time. My work benches are built with a heavy door for a top and base cabinets I scavenged from work. Lately I have toyed with the i…

I've got a D'angelico semi-hollow electric that's took a hit to one of the pots, breaking some wood and pushing the pot into the body. Not sure on the fix for this and can't find anything online, all suggestions welcome! Thinking of mounting an acrylic disk around the area to attach a long shaft pot to

Hey all! Anyone know what lacquer pigment might better match the deep black colour of this tele body? It’s an American tele deluxe with a nitro finish. Photos show: Finish damage was the size of a quarter. I’ve filled and levelled the area and sprayed on coat of Oxford black nitro. I poured a puddle of naphtha on to check the match and unfortunately no dice. I’ve used Oxford black many times for overspray during repairs and have always fo…

Okay gang I have a doozy of a crack repair. Young guy brought in a Epiphone LP Limited Ed. He had picked up the case while it was unlatched at the guitar took a nasty tumble. Severe finish damage, and the wood has a shear split in it as well. The undercoat is thick with a thin layer of nitro color on top. Spoke with a sweetwater rep and they said that the finish was nitro. Here's the guitar specs via Zsounds: Epiphone Inspired by Gibson…

Hey all, I’m curious to know people’s general thoughts on the appropriate or ideal saddle height after a reset. And, when to replace a bridge that’s been shaved down. I know there are a lot of factors (for me anyhow) and this question could open a whole can of worms when it comes to the specifics of the guitar, its age, style of bridge and desired sound. I’m providing an example I encountered recently, but would also like to know people…

I've only built a handful of necks and most of them have been roasted maple fretboards. This time around I am using a beautiful and incredibly stiff/hard piece of ebony. I am doing a light hammering in of the frets to get them seated and then using the hand-held vice clamps from Stewmac with the correct fretboard radius to push them down evenly the rest of the way. This process works just fine on roasted maple. It's just a softer wood t…

Hi all, I got a cheap Facebook marketplace guitar (“Olympia by Tacoma”) to try my hand at a bridge re-glue. The removal went okay, though I definitely learned a lot and will do better next time! The finish wasn’t masked in the bridge area, which is to say the bridge was glued to the finish, not the wood. I don’t know if that made it more prone to tearout or if that’s entirely explained by my lack of finesse with the pallette knives. Any…

I dyed an East Indian Rosewood bridge black to match the Blackwood fretboard before gluing it on*. The bridge is now glued to the top. What are some ways to "fix" that dye into the wood. I'm not crazy about TruOil - up to 40% mystery oil..... *I did a sample on rosewood with 4 different "dyes" and they were all stable, would not rub off with paper towel, naptha or mineral spirt. I went with the TransTInt. I did not however test with…

Hey! I have been working on repairing a d-18 that had a large hole in the side. I glued in a backer, cleaned up the edges and after a few attempts got a patch glued in and leveled. I have been testing finish on some scrap but am getting lost in the woods. In my tests I am doing most of the color in the grain fill. Does anyone have tips on how to start touching this up? Thanks!