The Hub

Hi all, I'd like to get some input on how to address this top blowout. For starters I own this, I got it as a project guitar, 71 D28. I'm not as experienced with acoustics as electrics and this is a big project but I got it to learn new skills and I'm confident I can do it with guidance. It had been stored in the case for many years under tension and was way too humidified. The bridge had pulled up I assume in stages. The center seam se…

Hi All, I wanted to check in with folks in the industry and ask for some advice. I have been on a building Hiatus for a number of years now (Hand Injury, Medical Issues). Things have gotten much better, and I am fully able and capable of building once again. The 2nd biggest hurdle I have had was a lack of opportunity for shop spaces to build. I now have a viable workspace and full use of my hands once again to build. The problem is that, o…

Hey all, I have been working with the work station for a few months now. I love it. I found a few little things that have helped me. 1. A mic stand to support the main beam. I bought the Total Vise version and it didn't work as well. 2. Rockler Bench Cookies as rear cross member supports. They have the correct 5/16-18 inserts in them and screw on easily. Now the thread rod has a sort of hi/low setting by just flipping it for acoustic or…

Where is everyone getting their shim stock from? Looking to buy blanks in bulk - mainly for electric neck pockets. Thanks!

I had a customer ask me to take a look at this electric guitar an "amp guy" did some work on. (if you couldn't tell by the size of cap he installed 😆) Seymour Duncan hsh pickup configuration. Is there any good or logical reason one would put the north start, finish and the south finish all on the same lug of a switch? The guitar plays but has more buzz on the hb settings than the single coil. I know how to rewire it to be more... traditi…

Hello Luthiers and Guitar Builders,We manufacture and supply high-quality natural bone Guitar Nuts and Saddles in custom sizes for acoustic, electric, classical, and bass guitars.What We Offer:• Custom-sized Bone Nuts & Saddles• OEM & Bulk Orders• Precision Cutting & Finishing• High-Density Natural Bone Material• Consistent Quality• Worldwide ShippingWhether you need a single custom specification or bulk production for your workshop or…

I’ve changed up my buffing protocols (again) and am selling off two lots of compound bars: -four bars ColorTone Fine, $55+shipping -three bars Menzerna P204 + two bars GW16, $100+shipping. USA shipping only. thanks, Creston

So today, while restringing a guitar, one of my techs dropped a .012 e string that slid down the wall and landed on a plug that was just slightly loose from the outlet. It landed just right and made a huge spark. No lesson to be learned here but a crazy thing to happen! We are changing our name to Sparky’s Guitar Service. 😬

Have an electric archtop that has a .012" backbow strung with 12-48s with truss rod completely loosened. 3 piece maple neck with a Ziricote fingerboard... Any tips or recommendations to straighten this neck would be appreciated... Currently trying humidity (in the case). Thank you! David O'

Since most of us fix or make guitars, we have probably heard something about the cease and desist letters Fender has sent out concerning the Stratocaster. I thought I would offer some thoughts. As always, caveat emptor. There are three basic ways to protect intellectual property under Federal law. Patent, trademark, and copyright. Each protects different things, and has different underlying legal theories. Lets begin with pate…

Rask Guitars — Utah (relocation required) Rask Guitars is a Utah-based custom shop dedicated to building exceptional instruments — primarily high-end acoustics, alongside electric guitars and prototypes. We operate with a small, focused team where craftsmanship isn't just a standard, it's the entire point. We're growing, and we're looking for a skilled, experienced luthier who's ready to plug into a real production environment, contribute…

Hi Folks Newbie here so please bear with me. I have a lovely early 90's Yamaha LD-10E acoustic in for repair, I think all solid wood? made in Indonesia and a lovely sounding instrument, however the electrics are letting it down. The pre-amp has a PCB populated with SMD electrolytic caps. Many of these have leaked and destroyed the PCB pads underneath. Repairing the traces is nigh on impossible so it looks like I'll have to replace t…

Hello — I would like to finish a mahogany electric neck and body with wipe on poly (probably Minwax satin) and would like to pore fill with Z-Poxy. I can’t find a definitive word on their compatibility. - Can I just wipe on the poly coats after block sanding the 2-3 Z-Poxy coats? - Should the Z-Poxy be sanded all the way back to wood or just smoothed/flattened? - Is a coat of unwaxed shellac between the Z-Poxy and the wipe in…