The Hub

Dovetail was 9/16” deep, and 1 9/16” wide at the back. 15th fret was 1 mm tail side of the end of the dovetail socket but a slight angulation towards the headstock landed in the right place. Hide glue, released easily. Nice everyday player, finish and binding beautiful, good spruce top, warped poplar neck.

This guitar does not have a dovetail. It has five dowel. Three in line and two at the top on either side of the truss rod. Remove truss rod nut before sliding neck straight out.

Here are some pics of 1918-1922 Gibson A3 "Ivory" Mandolin Dovetail Joint Measurements and Angles.

I am working on a neck reset on a Washburn Parlor - SN 283552. I have read that the 28 in the SN indicates that is was built in 1928, but the owner thinks based on her research that it was built before 1920. I am assuming a dovetail joint and that I can get into the neck joint for steaming by drilling into the 13th fret slot, but if anyone knows differently please let me know. The fingerboard extension has already separated slightly…

I’ve been speed modelling parts with the printer running 24/7 since inception. There are currently somewhere around 75-100 individual pieces modelled in my source file. Mostly only building on what I’m considering the X axis, but it’s Freeform so I’ve used them to build out Y.. anyways… Connectors, Extenders, Couplers, Links, Sleeves, Feets, Plugs, Panels, Hooks… and on and on. In a moments time, I will have a mass drop folder of Standar…

Great Tool. Great Benchy. Testing Threads, Sliding Dovetails, Overhangs, and it’s actually useful instead of that boat.. so testing wear resistance too. igus iglidur I151 Thanks for the model @member

I added measurements for the Yamaha FG red label FG 75's some time ago. I Keep getting these in for neck resets. I wanted to add photo's from the first one because they show that the dovetail joint does not align with the first fret beyond the neck/side to make folks aware so that one knows to slightly angle the drill to hit the pocket. I do the same on the holes drilled at the fret at the side/neck fret. I slightly angle the drill…

A Gagliano Jumbo probably made by Kay in the 1950's. It looks like this had a previous neck reset based on the shims and some sloppy chisel work. I removed the 14th and 15th frets because I had read that these might have a straight tenon. I didn't need to drill any holes for heat, as the spruce shims both split in half after the fretboard extension was released. The dovetail is about 11mm long, the pocket is 14mm deep, and the 15th fret…

Has anyone developed, or know of for sale, a fixture that can be installed in an acoustic body (dovetail neck) during finishing? I'm approaching the spraying stage of my build and would like to be able to have a "handle" on the body that I can use to hold & hang the body during that process. Regards,

I have an old epiphone archtop on my bench that I am struggling to get the neck off of. I think it's a 50's Zephyr (non cutaway, single NY pickup in neck position). Anyone have any experience with these? Is the neck not a dovetail joint? I'm no stranger to neck resets but this is putting up a fight as if it's been epoxied in place.

This is a Kamouraska classical guitar, model 111, made in Canada in 1979. Internet information says it was made in La Patrie, Quebec, and later the line became La Patrie guitars. It looks like someone has been into this one before as the dovetail fit was poor, the gluing is very sloppy, and there are some rough chisel marks on the face of the heel. Note that if you drilled holes at the 13th fret you would miss the pocket by a few mm. Th…

A friend of mine gave me his locally built mandolin for a neck reset. The glue in the dovetail has started to fail, and left a large gap at the bottom and a separation from the fingerboard and body. I've taken my brownstone and tried to heat the joint up enough to soften things up, but to no avail. I have no idea what type or where the joint is exactly. There are some indicators that this instrument was built with several flaws in the c…

I attach my necks using the LMII/O'Brien jig. No matter the method, there is no guarantee that the neck block and edge of the rim at the top is truly perpendicular to the centerline of the guitar. I’ve just flossed when things weren’t quite right. But now I take a long square, place it on the rim at the neck block and measure where the long square aligns on the top seam. I note Bass/Treble deviation at a known point (I use 290 mm).…