The Hub

Hello All I have been using Ted Bergstrand's online nut calculator on Benchmuse.com which is excellent. It allows you to have a consistent gap between each strings vs the progressive gap that the Stewmac rule gives you. Or you can do consistent centers to the strings. I have definitely found measuring the nut with calipers to work a lot better than the stewmac rule and don't use the rule anymore. I wanted some additional functionality…

Hey Looths, I have a 1980 Guild 12 string in the shop and while doing a preliminary examination I noticed this odd discoloration inside of the guitar. My immediate thought was water damage, although it hasn't bled through to the outside of the guitar and lifted the finish. I also thought of glue smear but I can't quite tell. Any thoughts here?

I've owned this Jersey City made 12-string/drone 'harp' guitar for a few years and want to get on the repair. I've taken the necks off many dozens of Schmidt-made guitars but never one with two necks. I've searched the web looking for harp guitar neck removal and didn't find anything of use. Asking for any tips/aids/experience from the loothers. My plan is to make a custom neck removal jig that fits the necks, and then drill the typical…

I'm restoring an old parlor guitar. I have just discovered that it plays 20 cents sharp. Thats not in and of itself a mystery, usually. This guitar however has exactly the same distance from the nut to the 12th fret, and from the 12th fret to the "saddle" which is now a small shim under the two E strings both are 12 3/32"...with room in front of the bridge pins to finesse the location of the saddle slot, which I have not routed yet) I s…

I have a customer with a guitar that has an intonation issue. It plays flat at the first and second fret on the D and G string. The factory spec says its a 25.5 scale but I measure from the nut to the 12th fret 12 5/8. I plugged the number for a 25.25 scale into the Stew Mac fret board calculator and the measurement is off from the nut to the first fret. Unfortunately I now longer have the guitar in my possession so I cant tell you exac…

Just wondering how normal the following is on Gibsons. When I run a straight edge from the 7th to the 15th fret on this modern J45 the 12 fret (and neighboring frets) are 3-4 thousands low. The result is fret buzz on the 9th to the 14th fret on the wound strings. Picture attached. Guitar is around 5 years old and otherwise in very good condition.

I recently picked up a Sterling Atlas 12 string that is in excellent shape except for some bellying, which once I get into setting action, may determine if I need to add a ‘bridge doctor’ to remediate some of it. However, I noticed that the saddle (adjustable but set to lowest point) has no curvature and there is not much down pressure on the center sets of strings which is causing some buzzing. My question is this (my first 12 string p…

I work in guitar repair for over 20 years and this strange buzz happen only 3 times and i really going crazy. Five years ago a all parts strat neck in G string, change string, leveling frets twice thinking i made a mistake, in some point i made a rudimentar neck jig to tried to repair that neck. Work in that guitar for 3 weeks and string heigth like 3.5mm and yeat, buzzing with not so hard picking just the G, even in other tuning like F…

Hi all, A customer brought in a 1970 Maton CW80 12 string...it needs a neck reset. Has anyone done this successfully (or alternatively have a sad story about how it's impossible)? I found one article detailing a workaround and showing a very odd neck architecture (https://harmensmusicblog.blogspot.com/2019/05/maton-cw-806-1977-dreadnaught.html) - doesn't sound/look promising....Any feedback welcome :) cheers, Steve.

I've got a 70s Martin D12-20 12-string on my bench (slotted headstock), it needs new tuners - the original tuners have several bent worms. The only 6-on-a-plate tuners I can find are the Golden Age from StewMac. The spacing looks right, but the Golden Age posts are about 1/8-inch shorter according to the specs on StewMac, 1-inch vs the 1 1/8-inch on the originals. Will that be a problem?

Hi Folks, I'm new here so I appreciate any input upfront! I had this guitar come through the shop and I've run up against something for the first time. The neck needs a little relief but when I went to adjust the truss rod the screw was already completely loose thus I couldn't perform that action. I tightened it just enough to get the truss rod nut to connect to the truss rod without making an actual adjustment to the neck in the wrong dire…

Model is "The '80". Daion built some nice guitars in the 70's and 80's out of a small shop in Japan. Nice old all mahogany 12 string. It's my instrument so doing a bolt on conversion. Forget about trying to get the neck off one of these (apart from Kung Fu) - neck construction seems to be based on multiple dowels (a bit like some Japanese furniture I suppose)