The Hub

I need some suggestions from the many great repair senseis out there.The customer is fine with a structural repair and not concerned about making it invisible. I told him you will see anything I do. He was fine with that and has a budget of between $700-1000. It's a clean break. nothing missing, It closes tightly.. I was thinking either 1) the generic double splines one on either side of truss rod and touchup as best I can. Or 2) the ab…

Hi all, I'd like to get some input on how to address this top blowout. For starters I own this, I got it as a project guitar, 71 D28. I'm not as experienced with acoustics as electrics and this is a big project but I got it to learn new skills and I'm confident I can do it with guidance. It had been stored in the case for many years under tension and was way too humidified. The bridge had pulled up I assume in stages. The center seam se…

Hello looths! Long time lurker, first time poster here all the way from New Zealand. I have recently acquired this 2008 Martin D-35 for a very cheap price ($1000 NZD - around 600 US!) it's dried out in a very cold environment and has two substantial cracks running all the way across the top, one large side crack, and a previous side crack repair that's been done quite poorly. I'm only about 3 years in to this repair journey and this is d…

Hi all, I got a Do Santos DSMSCC RC in shop, the Spanish heel has failed , or rather collapsed into the soundboard, splitting it on both sides along the grain, a broken brace just under the fingerboard extension , cracks on both sides on the top/side bindings, I measured wood humidity on the fingerboard 9% and inside the (very inaccessible) body 11% The normal procedure would be to re-humidify before jacking or clamping back into place ,…

A customer brought in a Gibson ivory top A3 mandolin. It's in good shape and has all the parts. He found it at the local thrift store here in Bishop. He wants it mechanically sound. Here are the problems: 1) Everything that comes into the shop has a shrinkage component and the effects of course very from instrument to instrument. This instrument is no exception and the results of that shrinkage, in this case, are severe. The top, ba…

I am repairing a damaged Stella parlor guitar. The original top was birch, plain sawn at 0.100 inches thick, ladder braced with multiple beefy braces and irreparably split, warped and generally separated from the sides. I want to keep the instrument ladder braced with a movable bridge and upgraded tailpiece, all firsts for me. I would be grateful for input on 2 issues. 1. The new top is Adirondack spruce that I’ve reduced to about 0.110…

All - looking for recommendations on overall approach for repairing this nasty side crack right at the edge of the tail block. My initial thought is that either the top or the back needs to come off in order to properly glue and clamp the main split. Thanks in advance. Images

Hi all, I am a newer guitar tech and after dozens of repairs this particular Simon & Patrick Luthier Cedar top SP6 acoustic dreadnought from the 90-ies with a bolt-on maple neck has been an incredible challenge. It came with a maxed out and stuck truss rod with a considerable up bow in the neck, extremely low saddle with barely any string break angle, so it needed a neck reset. Later on I figured out that it also has a pretty dras…

Hello again folks, how is everyone! So I'm curious about what people here think about re-tops, who's done them, and what sorta ballpark rates you've charged for past completed jobs. I've got a bit of a wild one here, so strap in if you've got a couple minutes for story time! Back in 2012, I traded an HD28V of mine for a cool 1966 D-35 that needed some work. Basically, the body and neck of the guitar were fine apart from…

Hi, thanks for this great resource. This is my first post here. I work on my own instruments and have little experience with advanced repairs. Recently I acquired a ca. 78 Sigma DR28H. I bought it because it sounded great and came with a pickup installed. I wanted something for open mics and gigging. With light strumming it sounded fine but I found some buzzing when I took it to a jam. I made a nut and saddle , adjusted the truss…

To repair previous "repairs" I removed the back of this guitar. I'm considering setting the neck by slightly pulling the block back whilst gluing on the back. If the seam on the bottom of the guitar where the back and sides meet is within easily workable amount (see by doing a dry run) then hmmm...the concept has my attention! I could otherwise just do a regular neck set. Votes? Thoughts?? Images