The Hub

Hey guys. I guess this is an old topic, everyone talks about it but I haven't been able to find a definitive solution for this. Here's the deal: I'm working on a PRS Silversky that has this old problem that when you use the trem bar, one string (G in this case) goes sharp. I made a few adjustments to the nut as we all know that's the first thing to look at...no good. This guitar is new so I'm pretty much ruling out the bridge and posts si…

First time making purfling to match a repair. Problem: couldn’t get it to bend without delaminating and cracking. Veneer is 6 plies using 4 of SMs 0.023” and 2 maple at 0.025” cut to 1 1?2 inches wide. Glue up with Titebond Veneer glue, final stack at 0.140” thick. Let it dry 2 days, cut a few 0.090” strips, then used some super soft just at the waist and despite going very slowly the strip skewed, delaminated and started to break plies. W…

I am working on a neck reset on a Washburn Parlor - SN 283552. I have read that the 28 in the SN indicates that is was built in 1928, but the owner thinks based on her research that it was built before 1920. I am assuming a dovetail joint and that I can get into the neck joint for steaming by drilling into the 13th fret slot, but if anyone knows differently please let me know. The fingerboard extension has already separated slightly…

I've got a PRS SE A50E acoustic in with complaints of high action. Checked the relief and it was sky high. Tried to flatten it, and it wouldn't go, so I started experimenting. When there's no string tension and the (single action) truss rod is slack, there's loads of relief. Tightening the truss rod works fine and the nut turns easily until the neck is flat, then resistance goes up but the neck won't go past dead flat. It behaves as…

I’ve had success placing Titebond under top braces using an artificial insemination catheter (not the AI you thought!) The catheter is PVC, 11 inches long, has a standard Luer hub for syringes and is thermoplastic so it’s shapeable. Purchased on Amazon Weewooday 50 Pcs Disposable Artificial Insemination Rods Disposable Breeding Rod Tube Flexible Breeding Catheter Tube for Dog Goat Sheep(10.8 Inches,White) URL = https: //a.co/d/03SDiw…

Hi everyone! I'm trying to wrap my head around this problem. I was doing some fret on a throwaway neck and found a couple of uneven frets in the middle of the neck. (I made sure to seat them down before levelling too!) While levelling, I came across an issue where the first few frets and the last few frets were being sanded down before the middle frets. I did make sure the neck was straight with a notched straight edge and the StewMac n…

Refretted my Yamaha Studio Lord 550 with jumbo frets. This is my second fret job. First was on a bolt-on BC Rich neck. The Studio Lord (Les Paul copy) was my first set neck project. It is pretty good. No fretting out. I set the action at 4.5/64 on bass and 3.5/64 on the high strings. Today I noticed that if I bend a high F to G (13th fret on first string), the note frets out (I can get to F # no problem by bending from the 13th).

This may be a stupid question. A client has a Bartolini jazz guitar humbucker with no brackets, 5JNB: https://bartolini.net/product/5j/ They want to attach it to an ebony jazz guitar pickguard. How do you do that? My thought was to make a metal tray, bend it to the appropriate shape, screw it to the pickguard, and attach the pickup to the tray with double stick tape. Does anybody sell something like that? Or alternately, how do you attac…

Hi Gang, Has anyone switched out the plastic, 8 pin box output 18 volt active/battery switch output jack on a P Bass special for a standard TRS output jack or some other? I just got off the phone with Fender and they don't make this anymore and they recommend replacing with another plastic box from Molex and are sending a wiring diagram. The problem with all this is the plastic boxes have wimpy thin spring steel and wear out quickly.…

Hey everyone, I could use some advice as far as the fretting process is concerned. I’ve been doing guitar repair since around 2008, I opened my business doing guitar repair in September of 2021, and I’ve always felt that fretwork has been the most challenging part of this job. I’m getting to the point now where I finally feel like I’m getting the hang of it, but I’m not where I want to be yet. I should mention that I use the Erlewine…

Hallo, I have an old archtop (plywood) that needed a refret. There is no trussrod. I talked to the owner, he knows that my work will maybe/eventually more expensive than the value of the guitar. But it was only after leveling the fretboard that I realized that the fret slots are completely off. I talked to the customer again, and we agreed, that I should put a new fretboard on the guitar. I have one, that I took of an old guitar, and reuse…

So I've ended up with a 1961 Harmony H54 for free. The neck has about .022" of relief without strings on it. The fretboard was taken off long ago. I got it like that, it was just stuck on with double sided tape. I have no clue why it was taken off other than maybe someone wanted to fix the excessive relief and changed their mind. It looks like the original steel reinforcement rod was never actually glued in. It seems like it was bent a…

I have a new client with 100+ shredder type guitars. He gave me a couple of the easier ones to work on. The first is an ESP which fretted out with bends up above the 12th fret. I thought it was just the 2/64th" low action, but the last two frets seemed really high. I suspected there was a shim in the pocket, and yeah, there was. The bottom of the neck heel is deformed where the shim was. The shaded/dirty area at the bottom edge. Not den…