The Hub

Hi everyone, Every once in a while, I come across a bass that simply refuses to stop buzzing. Right now, I’m working on a bass (I won't name the brand, but it’s in the €2,500 range) that has a slight fretboard hump near the neck pocket. I figured that was the culprit, so I performed a fret level under string tension. The frets are now perfectly level... yet, it continues to buzz across the entire fretboard, even with fairly high a…

I found a cheap double bass in pieces on Facebook Marketbook, so why not try to bring it back to life? Note, I can't play, so look over the awful hacking during the sound clip 🤣

Seeking referrals for a machinist or fabricator to replace the bass side of the rolling nut on a 93 Charvel Surfcaster. The original had been lost and replaced with something similar but not the correct dimensions and taper. Thank you, Mark Images

Hello, Looking for any suggestions for replacing the missing hex nut on a Pedulla Bass. This is not a standard size and from limited past experience this is fixed to the end. A flat 5-6 mm nut seems to fit but not securely without removing material under the nut shelf. Thank you, Mark Images

Hello, One of my commissions is coming down the pike and it's going to be my first time using bar frets. I could use a once over for any helpful tips if you have any. About the guitar: Aged HD-28 but mahogany back and sides. I think Martin called this a HD-28 M? Skipping the truss-rod and using two carbon fiber strips. My process for Frets: 1: I CNC my fingerboards to a 16" radius and for T-frets I use a .023" to cut slots with a mat…

Any suggestions if this can be saved? It is a neck I received for free upon replacing it for a customer. The wood was missing and the rod is missing the adjusting nut. The truss rod had pushed the inlay out as well as the wood damage . I wasn't sure if it could be a structurally sound repair. I have no idea of the neck rigidity or action with strings. I wont be online because of a previous dr. appointment but I figured it would be a go…

Hello, I have on my bench and es-125 with a concaved belly in the top where the bridge sits, I was able to fit a feeler gauge under one of the braces in the area, the brace above the bass side. The back of the guitar is loose for a stretch of roughly 5 inches. My thought was to take off the back and address the braces and somehow address the warp in the top. Any thoughts on how to unwarp it or better approaches to the whole job?…

Hey all, My father-In-law would really like to make a rickenbacker 4003. I’m based in the UK and I can’t find a suitable template/templates for this. I wasn’t sure to post this in the CNC forum but thought I’d post it here first. I have tried crimson but no luck, but they’ve mentioned many people have asked about them. Thanks for any help it’s much appreciated

Hi everyone - I recently ran into trouble making new nut for one of my necks that needed to be trued and re-fretted. I roughed in the nut as usual and then, with the bass guitar fully assembled and strung up, I started cutting the slots to depth. I use the StewMac digital nut slot depth gauge and have had good results in the past. I marked the nut's lowest points (radiused) using the guitar nut scribe tool (first time using this!) and c…

We at F Bass Inc have been crafting boutique basses out of Hamilton, ON since 1978 and we’re looking for a Master Builder to join our small but mighty team. Applicants must have a sharp eye, strong organizational skills and the ability to problem solve in creative ways. Someone who genuinely loves crafting custom instruments and appreciates the little details even more so. If you pride yourself on precision and creativity and get a kick…

This jazz bass has come in with a cracked and separated fingerboard near the nut. I believe this is an early Bi-Flex but am not entirely sure or familiar with them. The truss rod is functional and tightens up when turned. Top of the walnut plug is missing and the washer appears to be crooked or dislodged. Not sure what purpose that washer serves. This is probably the thinnest bass neck I’ve ever seen and it’s no wonder that this fingerb…

Hey everyone, I have a Vaccaro bass guitar and I'm getting a lot of open note buzz on it. In truth, the bass could stand a refret but that may or may not be in the cards. Additionally, the truss rod nut is stripped. I'm also wondering if this nut is designed to come out? I imagine it is but it's kind of funky. A 1/4" Allen wrench is still too small to grip it. So the questions: 1. How would you deal with the zero fret and the nut? The st…

Looking for some guidance here – I have a 1973 Jazz Bass with maple fretboard and fretboard binding in for a re-fret. The finish is of course built up thick and crackly along the frets, and although they’re not seated too nicely, the first few came out really tough and chippy even after scoring the finish really well. I’m aware that Fenders were fretted sideways until 1982, but because of the binding, pushing them out sideways is not an…