The Hub

OK I know I just posted here, but I just had a tremendous customer service experience and had to share. I contacted Guitar-Restore.net about this, they had a similar graphic to what I needed for my Harmony, but it was on vinyl instead of a waterslide decal. They not only made one available for me, they just added it to their site!! Couldn't be happier. So if anyone needs custom decals or graphics for a project, I highly recommend th…

I'd like to start a discussion about guitar polishes. We have always been careful to use only non-silicone products on nitro finishes. We previously used Stewmac Preservation polish for years, but they don't offer that product anymore. We recently had maybe what was a bad batch of Stewmac "Clean and Shine" that was softening nitro finishes so we trashed it and haven't purchased anymore. The first bottle we got worked great, but the s…

Any recommendations for custom decal suppliers? I thought I had seen a discussion here at some point about this, but I can’t seem to find it if it actually does exist. I used to have a guy I ordered decals from but I haven’t been able to get up with him even though his website is still open. I was thinking some of the collective brain trust here may be able to help me out with this.

Hello folks, I recently purchased some dental articulating paper to use for my neck resets, and to my chagrin it arrived as a smaller length than I anticipated. It is only 18 mm long, which is only enough for about 2/3 of the length of the mortise. I’ve tried to look up other brands, but none that I can find listed their dimensions. Does anyone recommend a brand or variety that is adequate length? Thanks!

I recently realized its probably time to retire my cheap set of jobber drill bits (Robert Oven standard issue) that are almost a decade old at this point. Does anyone have a set they like or a brand they would recommend?

Hello, This is my first discussion as I am new to this group. I am starting a restoration project on a 1957 Gibson LG-1. The first job on it that I want to tackle is to replace a broken back brace. It appears to be broken in half right on the center line (see pic one before the brace was removed). I have removed it and am gluing in back together (pic 2), just to get it strong enough to use as a template for fabricating a replacement…

I drew up and printed these F hole plugs for a customer a little while back, felt like showing them off here. The bottom diamond shaped piece has a M4 nut in it, and is super glued to the body of the plug at its two tips. An M4 screw threads into the nut through the counter-sunk hole in the top of the plug. The entire plug drops into the F hole, and then you can tighten the screw slightly to expand the plug so it clamps itself into plac…

I'm interested in getting people's perspective on string height. I've seen recommendations for a standard string height based on the instrument type (such as https://www.stewmac.com/video-and-ideas/online-resources/neck-building-and-repair-and-setup/string-action-gauge-instructions/). But this doesn't take into account how the instrument is used, playing style, and personal taste. What would your recommendations be for the following sc…

I have a 70s PBass with a maple “A” neck that could use a refret. It still seems to have the original frets. I tried a level and crown on the already low frets, but I think it needs refret. The frets in the money area are pretty low, .030-.025 and I’m concerned about removing them sideways, as I’ve never had a chance to do that. I understand from the fretorama with Joel Wilkins that when they are this low it increases the difficulty of…

Hello! Brand new member here following the recommendation of Rick at Gluboost. He suggested that I reach out to this group to get help with my restoration project. I'm actually looking to restore vintage dining chairs (6) that have chips on their black lacquer finish. Rick confirmed that Gluboost should be a good option for refinishing the chairs but I'm having the hardest using the product to get the results I want (sad photos attached…

Hi Gang, I was finishing up a new guitar and discovered a rattle that I think is the truss rod. Strange that it did show up until now. I always rap on the neck to make sure the truss rod does not rattle before I begin finishing. Anyway, I finished the setup and was recording the final frequency responses (like Gore and Giuliano Nicoletti) and the rattle only happens when I tap the bridge with the sound hole blocked. Anyway, it sounds l…

I had a customer contact me and he told me that he has a Zager ZAD80CEOM and that the bridge is staring to raise at the back. He says the gap is about 1/32" and would like me to remove the bridge and reapply it. I have yet to see the guitar in person and I'm a bit hesitant to take it on. I've never performed this type of operation before, although I do have some theoretical knowledge of it, just not practical. Some of the question I hav…

Hello guys Someone get me this Taylor c416 to my workshop. Alot of blushing and milky finish . What are ur recommendations Shall I sand it ? Or any other tricks the client does mind the scratches. Note I measured the wood humidity is 15 %

Hi All, I have a J-15 in with some finish burn on the back of the neck. I'm wondering what you'd recommend as a repair? Lacquer, Fill N' Finish, something else?

Not sure if this is the best place for this, but whatever. I need somebody to check my logic here--I could be completely wrong in my thinking. I'm about to start up my new shop in Ireland, and the humidity/temperature situation is VERY different than the Greater Washington DC region. I will also be unlikely to have as complete control over temperature and humidity as I did in our extremely tight, air-conditioned house in the US. I also k…

I just wanted to put in a plug for classicalguitartuners.com and Zebulon Turrentine. I was looking for some single classical tuners for a 7 string project and found his website. I was a little confused at first because he catalogs all the available tuners including ones that he doesn't sell but he supplies Der Jung (from Korea) and Gotoh tuners among others. I believe he can also get steel string tuners. The service and shipping…

Long story short, Mom's sitting next to her guitar and POW, the bridge pops off taking part of the top with it. Now I'm trying to figure out how to fix it and I would like your feedback on my plan below. The hole is roughly the same size as the bridge. The top is a 3-layer laminate. The bridge, top, and bridge plate all came out as a single unit. The glue on the braces behind the bridge has failed, so the top will need to be re-glued…

I have an Epiphone explorer that suffered a vertical neck break in shipping. I'm in the middle of repairing the break a la Ted Woodford's remedy. My question is, what would be the polyurethane you'd recommend to cover the break? A couple of things to consider/questions I have: The neck color is not quite all the way black but the customer is fine with it being darker than the original color. The neck finish is satin What would be the best…