The Hub

I have this 1970’s guild that had the finish burned from the cradle of a guitar stand. I am having issues with the border of the repair darkening. I sanded back the damaged area and the surrounding finish which was gummy. I used water based pore filler as a starter, a few sealer coats, and then clear coats (one of the coats with some dyes). Any suggestions at how to get this looking better?

Being new here, thought I would post an introduction. My name is Paul McGill Mcgillguitars.com I have been making guitars since 1976. I have lived and worked in Nashville since 1985 when I relocated here to work in the repair/restoration shop at Gruhn guitars. 410 Broadway, now a novelty shop. I was there a short time before commiting full time to guitar making as I had done prior to moving here. My main influence as a guitar maker was Ro…

Hi everyone. I have begun to incorporate more rattle can toner work in my touch up and cosmetic repairs. I have been using Mohawk toners so far and I am now trying out a different one of their toner products that is new to me. I use Mohawk Ultra Flo Ultra Bond for my clear coats. I thought it might be helpful to have a dedicated thread to the topic of rattle can toner as it pertains to touch up. Particularly headstock breaks that incorp…

Hoping to get some input on this touch up. Auxiliary pieces of rosewood were added to cover up the screw holes from a previous bridge many years ago. The footprint of those pieces was scored, in some cases deeply. There were spots where top material was missing. I grafted pieces from under the bridge footprint which (along the same grain lines ) I will replace prior to bridge glue up. The challenge here is the inability to blend bey…

My heat blanket left some blushing in the finish on this 1970s Japanese guitar. The bridge was epoxied on and I got it too hot. I’ve used a heat gun to warm the finish (the blushing goes away) but it comes right back when it cools. Am I stuck with removing the damaged finish and touching up?

I'm trying to touch up a finish ding and a couple of sand through spots on a black, mid-2010s MIM Fender Telecaster Deluxe, and I'm having a really hard time doing it well. I did a previous touch up on a black Squier Jaguar using Stew Mac's black nitrocellulose rattle can, and it blended so well I can't see the repair, but in this case the contrast between the original finish and the touch up paint is super obvious. I've since learned h…

I'm looking for advice and feedback on this touch up. It's my second one of these carbon fiber fabric repairs, my first turned out much better. I used the powdered pigments to match the color of the original wood, which was exposed along the margins of my repair, then I used glass slides to match the color of the lacquer. I then used The Mohawk brush tip marker, which I don't think I'll use again because I couldn't get straight lines.…

Hi everyone! I'm looking for advice about heat treatments for a warped neck, I know they are a thing but I've never actually done one. I have an Epiphone Les Paul in the shop that originally I was only going to do a level/crown/polish and a setup on, but when I tried to adjust the truss rod and checked the fingerboard with a straight edge I noticed there was about .030" of relief in most of the middle section, which was pretty consisten…

Introducing Poseidon’s Horn! Coming in just shy of 18”, this tubular behemoth is the ultimate mess-free humidification device for closing up those pesky top and back cracks prior to repair. It’s dry to the touch and holds 1000ml of water! The days of finessing a Tupperware through a sound hole are over. Cheap and quick to make! Parts list (Supplies to easily make 10 of them) . Water beads - https://a.co/d/5v5Q2da . Braided sleeving - https:…

After watching Jeff Jewitt's Touch Up for Builders video, I began looking for a source with a selection of pigments like he has. I started by looking at Mohawk Blendal powder stains, but they only had 6 of the 12 pigment colors I was looking for. I widened my search, and exchanged e-mail with a couple of Etsy vendors. I was fortunate enough to find KonstantasShop which offers 24 pigment colors. While I suspect this collection is targete…