The Hub

Question about splines: At what point are they necessary? My question is primarily regarding the crack to the left between the bridge and the sound hole as well as the crack at the upper bout that runs along the fingerboard extension. I have already glued them both and used the TJ cleats that run the full length of the cracks. I have already splined the lower bout crack that runs from the bridge to the binding as it was super gappy and d…

Rask Guitars — Utah (relocation required) Rask Guitars is a Utah-based custom shop dedicated to building exceptional instruments — primarily high-end acoustics, alongside electric guitars and prototypes. We operate with a small, focused team where craftsmanship isn't just a standard, it's the entire point. We're growing, and we're looking for a skilled, experienced luthier who's ready to plug into a real production environment, contribute…

An old friend of mine, Les Stansell, who has been building some pretty high-end guitars and ukuleles for over three decades has had to close his shop for health reasons and is looking to sell all his tools and equipment. I’m spreading the word to help him find a suitable buyer – hopefully a new luthier ready to set out on their own. If someone is interested they can contact me here and/or contact Les directly at [email withheld]…

Hello again folks, how is everyone! So I'm curious about what people here think about re-tops, who's done them, and what sorta ballpark rates you've charged for past completed jobs. I've got a bit of a wild one here, so strap in if you've got a couple minutes for story time! Back in 2012, I traded an HD28V of mine for a cool 1966 D-35 that needed some work. Basically, the body and neck of the guitar were fine apart from…

Hello all, got a problem in a telecaster I rewired that has me in a twist. The basics: friend has a 2001 US Standard telecaster (left handed not that it matters). He bought it used and says it was quiet initially. A few years back he grabbed the pickups out of it and moved them to a new tele body with a torrefied maple neck he preferred. Recently he upgraded the new build with a Lollar CC tele set, and asked me to reinstall the original…

Hi all. Brand new member. I’ve been building a classical guitar via kit from LMI for a couple of years now. I keep putting it off but recently became motivated to get back to it. Unfortunately LMI is out of business so I now have no one to go to to ask questions. I’m at the stage where I’m putting the sides together in the form. I followed the dimensions for the form based on the plans as I measured them, but the sides overlap pretty ba…

For those of you who regularly do semi-hemispherical frets -- how long do you make your frets? Specifically for a bound fretboard (although I suppose this would apply to either bound or unbound) do your frets come up a little short of the outside edge of the binding? And if so, how much gap do you leave? I did my first semi-hemis on a new build and made them end flush with the outside edge of the bindings, but it doesn't feel right.…

Hi all. I'm in the process of working with a landlord to customize a space for my growing repair and building business. The space is approximately 800 square feet and broken into a major space (around 400 square feet), and 2nd large space (around 300 square feet) that I'm thinking of as a machine/sawdust room, and 2 smaller areas that I'm considering as a spray booth and a wood/guitar storage closet. I'd love to hear about lessons learn…

I’ve been building electric for a few years but decided to make an acoustic this time. I have some German spruce panels I was going to use for the top. While running it through my drum sander to dimension it, I noticed that both panels have matching 6-8” cracks so the original blank must’ve had a split pre resawing. Would I still have good results if I glue the panels and move on or should I buy a new top set? (I can’t return what I have…

Speaking of Trevor Gore... I've started using falcate bracing on my ukuleles and in making the braces, 3 strips of .0625" spruce are bent and then put in a bent lamination glue up rig using epoxy. Bending spruce is no fun on a hot pipe. It's slow, fussy, the fibers want to delaminate. I have been thinking about building a small dedicated steam box. Pulling all 3 of the strips out at once and bending them over a form with a metal back…

Hello. I am interested in the luthiers opinions about using Osmo oil as a finish on acoustic guitars? Advantages vs disadvantages. I am a new builder with small home workshop, mostly using hand tools to build my first acoustic guitar, an OM pre war style. Thank you all.

I bought the O'brien vacuum clamp and a pump to clamp bridges on new builds, but also to use for repair work. I got tired of making custom top and bottom cauls for every odd-shaped bridge that comes in my shop. The vacuum clamp works great on a flat surface with no pick guard. I put it on a J45 with a pick guard, and it won't seal. The gasket is too hard to form over the pick guard. I've seen YouTube videos of other folks using vacu…

Hello All! My first post and I'm very happy to be here and share the highs and lows of this pony ride. After years of bending sides on a hot pipe or bending machines belonging to 'other people', I finally built myself a bending machine. Functionally it is great, but the result on some test material was far from great. See pictures attached. What you see here is a doug fir 'test side' that certainly came out guitar shaped, but oh my, what…