The Hub

Few more prints up for grabs to anyone in the US who responds first. Fret sander and two screw holders with the gridfinity lobbed off so they are just free-standing.

So it seems that a drum sander would be very handy for many parts of a "build from scratch". There are a few out there that cost under $3000.00 that can handle wood up to 4" thick and are wide enough to sand a back or top after the halves have been joined. Jet JWD-22-44 open stand, 22"width Jet JWDS-2550 open stand, 25" width SuperMax 19-38 opend stand, 19" width SuperMas 25-50 closed stand, 25" width Questions: Any recomendations on the sa…

Good evening folks, lately I'm experiencing some sanding methods/mechanism frustration. Can't explain better than look like I'm regressing at doing it. The only thing changed in my building routine is that I'm currently using a CNC (I haven't used one for some years) for both bodies and necks. I have no problems with necks, but sanding bodies has become incredibly frustrating, specially around the edges. While I keep improving my c…

Well, I have exhausted all the internet can offer for options for a replacement bridge. The customer, long ago, removed a ton of material from the bottom(!!!!) of the bridge, and now that ive taken this guitar on as a restoration, its up to me to make a new bridge. I have found some ultra small pattern bits, and round-over bits to do the inside of the mustache flush, but I can not for the life of me decided how im going to cut the bulk…

Hi all. Brand new member. I’ve been building a classical guitar via kit from LMI for a couple of years now. I keep putting it off but recently became motivated to get back to it. Unfortunately LMI is out of business so I now have no one to go to to ask questions. I’m at the stage where I’m putting the sides together in the form. I followed the dimensions for the form based on the plans as I measured them, but the sides overlap pretty ba…

Finish Sander Location: Athens, Georgia Schedule: Flexible, Monday–Friday Pay: $16–$19 per hour (depending on experience) We are seeking a Finish Sander to join our small shop in Athens, Georgia. This role focuses primarily on dry scuff sanding and wet sanding as part of our finishing process. Buffing training will be provided as needed. This position is centered on learning the intricacies of sanding and surface preparation. Spraying is n…

We at F Bass Inc have been crafting boutique basses out of Hamilton, ON since 1978 and we’re looking for a Master Builder to join our small but mighty team. Applicants must have a sharp eye, strong organizational skills and the ability to problem solve in creative ways. Someone who genuinely loves crafting custom instruments and appreciates the little details even more so. If you pride yourself on precision and creativity and get a kick…

I’ve been building electric for a few years but decided to make an acoustic this time. I have some German spruce panels I was going to use for the top. While running it through my drum sander to dimension it, I noticed that both panels have matching 6-8” cracks so the original blank must’ve had a split pre resawing. Would I still have good results if I glue the panels and move on or should I buy a new top set? (I can’t return what I have…

Santa heard I had a challenging year so he got me a 3d printer for Christmas. I’ve been printing like crazy, learning the machine. This has resulted in a bunch of tools that either don’t work for me, were attempts at mixing colors, or have very minor printing blemishes. Two lots up for grabs to anyone in the US who wants either. I’ll mail to you for free. First one to claim each gets it :) First lot has parametric nut and saddle sanders…

I watched the Guild F-20 video (https://dev2.loothgroup.com/groups/repair-and-restoration/forum/topic/cracker-x-braces-on-guild-f20/#post-60310) with great interest since I've been working on a Gibson L-3 with a similar problem. A little back story - The original repair request was to address a small pickguard crack on the sound hole side. After peeking inside, I saw 5 loose brace ends on the treble side. Still a pretty standard repair…

Here are some pictures that show the basic elements of a dome sander I made. Critical part is a lawn mower blade bearing/spindle. Cost $63. It is marked part # 607418 Blade spindle assembly. It has a tap for a .625-11 bolt on the side I put facing upward to bolt on the disk, and a shaft with a keyway on the bottom to attach to the big pulley. I used a 11” diameter and 2.5” diameter pulley combination. This gives just about the perf…

Like many of us, I work in a small space - a quarter basement with maybe 6 -1/2 feet of headroom. Sawdust is a problem. There’s no room for an extensive ductwork system or a blower setup. My shop tools (bandsaw, drill press, vertical belt sander, etc.) have a 1-1/2 inch connection for vacuum, but I have mostly been too lazy to use them. (note that I finally added a portable shop air cleaner with HEPA filters). When the most recent Wo…

I'm between shops right now and have a bunch of lutherie tools in a U-haul storage facility on 4th ave in Brooklyn. Here are a few of my local craigslist posts. I've also got a bunch of wood I'll be listing in some form or another. Let me know if anyone would like to come by and have a look. Use the "more ads from this user" link in CL posting to see updated and additional listings. thanks! https://newyork.craigslist.org/brk/tls/d/brookly…

Im going to be starting my 6th acoustic build soon. One issue I continue to have is low spots on the sides. I use an LMI bender with the spring steel slats that LMI provided (they are pretty stout). One observation, sometimes there is a bit of rebound in the sides as I take them out of the bender. I sort of force them into the mold to glue the neck and tail blocks. I’m wondering if that may be where the issue is occurring. After removing…

I have 2 of these and need only 1. It is a beast of a machine with 1-1/2 horse power. I am in Parma, Ohio, local pickup only. Here is the Craigslist link: https://cleveland.craigslist.org/tls/d/cleveland-jet-jsg-6dc-belt-disc-sander/7838835179.html

Has anyone ever used the belt-sander spline process for a headstock repair? It’s when you glue up the headstock then push it up against the rounded edge of a belt sander to remove a rounded chunk of wood, then patching the chunk by sanding down a rounded spline to fit it. Seems much easier than routing channels because you can put sticky sandpaper directly on the sanded-portion of the headstock/neck and shape the spline perfectly to the…

Hey all. I've got the above-mentioned guitar on my bench. It had a neck reset and what appears to be a new bridge pad put in 14 years ago. It's a crack-free guitar except for a couple of little hairlines running from the back of the bridge to the upper tone bar. I thought that was a bit weird. Inside, everything looks okay until I turn off the inspection light, at which point I can see the rosy glow of daylight through the top - this…

Hey everyone, I could use some advice as far as the fretting process is concerned. I’ve been doing guitar repair since around 2008, I opened my business doing guitar repair in September of 2021, and I’ve always felt that fretwork has been the most challenging part of this job. I’m getting to the point now where I finally feel like I’m getting the hang of it, but I’m not where I want to be yet. I should mention that I use the Erlewine…