The Hub

Beginning Friday, August 31, I'm opening up the shop every Friday from 2:00–4:00 PM EST for an informal Zoom session. Whether you're: 🔹 Building with a Strings Micro Factory kit 🔹 Thinking about getting started 🔹 Looking for advice on a current project 🔹 Or just enjoy talking guitar building... You're welcome to drop in. No presentation. No agenda. Just open shop. Bring your questions, share what you're working on, or simply stop by and say…

Hello, I just received an unfinished, slotted but not fretted maple neck from Warmoth. I believe standard practice is to fret then finish but I’m curious if it might be better finish before fretting? I understand one would want to prevent finish from entering the slots. I’m and going to use tru oil and do a light finish, maybe three or four light coats. Thoughts for this beginner? Dave

It was attacked by a Martin Dreadaught on a small mountain stage resulting in a faceplant. The top is Redwood. I was able to get it to glue up fairly well and have done some splice and drop fill on the vertical cracks. I'm curious about suggestions for the deep cross grain areas. I am hoping to not re-shoot any lacquer and just rub out the finish with some Kovax dry sanding. It was never high gloss buff to begin with and it's a personal…

Hello looths! Long time lurker, first time poster here all the way from New Zealand. I have recently acquired this 2008 Martin D-35 for a very cheap price ($1000 NZD - around 600 US!) it's dried out in a very cold environment and has two substantial cracks running all the way across the top, one large side crack, and a previous side crack repair that's been done quite poorly. I'm only about 3 years in to this repair journey and this is d…

Hey everybody, I should restore this Roger Rossmeissl Archtop. There is a lot of work to do. The owner is aware of the possibly-much-more-work-than-value situation. I am still thinking about how to aproach it, I want to start working on the guitar in August. It seems that there is not much warping in the top, few wood is lost. I do not know what happened to the guitar, but sometimes I hear a voice coming out the corner of my workshop mumb…

I've built a number of classical guitars with an adjustable neck and they seem to gather quite a bit of interest, so i'm currently in the process of looking to refine the design and build. It's quite a simple construction where the neck is held together by string tension and hangs on a pivot. I developed a 3d printed "socket" which acts as the interface between the body and the guitar and allows for some fine tuning of the alignment of t…

I've owned this Jersey City made 12-string/drone 'harp' guitar for a few years and want to get on the repair. I've taken the necks off many dozens of Schmidt-made guitars but never one with two necks. I've searched the web looking for harp guitar neck removal and didn't find anything of use. Asking for any tips/aids/experience from the loothers. My plan is to make a custom neck removal jig that fits the necks, and then drill the typical…

Anyone have plans/drawings for a vintage spec AJ they can share, or a link where I can buy them? I haven't been able to find anything other than J45 plans with general notes on the differences that aren't clear enough to follow. Thanks!

Hello! Im working on a repair for a cutsom build for a customer. Its a Dunable Yeti built in 2022. Anyway, all work was going fine till testing the rod... i discovered that the rod is working the opposite of how it should function on any other guitar. CCW is tightening (and no, no a dual action rod) Tightening this rod is adding relief. The guitar already had too much when disengaged. Trying to figure out how to approach this as this is a f…

Hi, I am still a little confused by the new look of the forum, hope this is the right place to ask. Which fretwire would you recommend for a refret of this 70s LP? The current frets are 2.75mm wide, but dressed down to 0,35mm height. I have heard storys about frets that are this low but never seen in real life before :-) (0.108" wide and 0.014" height). Thank you in advance :-)

Hello all! My name is Jake and I run a repair shop out of my NYC apartment. I am looking for someone who's experienced in CAD to help me with a project. I am working on a 5 string headless bass build for a customer. The neck & body are to be CNCed by a local mill here in Brooklyn, NY. I have a 2D design (PDF and CRD), but I need help making some modifications, as well as translating it to 3D. Pay is negotiable. I will basically pay whate…

Few more prints up for grabs to anyone in the US who responds first. Fret sander and two screw holders with the gridfinity lobbed off so they are just free-standing.