The Hub

Where is everyone getting their shim stock from? Looking to buy blanks in bulk - mainly for electric neck pockets. Thanks!

I'm restoring an old parlor guitar. I have just discovered that it plays 20 cents sharp. Thats not in and of itself a mystery, usually. This guitar however has exactly the same distance from the nut to the 12th fret, and from the 12th fret to the "saddle" which is now a small shim under the two E strings both are 12 3/32"...with room in front of the bridge pins to finesse the location of the saddle slot, which I have not routed yet) I s…

Good afternoon all. I have started the process of removing all the binding from the old Country Gentleman and it's going well. I did discover after removing the strings that the neck is pretty loose and moves around quite a bit (no surprises there). I removed the black plug on the back side of the body then removed the large regular (slot) screw that holds the neck in place. I thought the neck would just slide out considering how loose…

A Gagliano Jumbo probably made by Kay in the 1950's. It looks like this had a previous neck reset based on the shims and some sloppy chisel work. I removed the 14th and 15th frets because I had read that these might have a straight tenon. I didn't need to drill any holes for heat, as the spruce shims both split in half after the fretboard extension was released. The dovetail is about 11mm long, the pocket is 14mm deep, and the 15th fret…

Hey everyone, I wanted to do a bit of a follow up on a repair I'm doing. A customer brought in a Seagull acoustic guitar that had been dropped, causing the heel block to separate. I managed to get that glued back together with pleasing results, however I did need to take the neck off by removing the two bolts which thread into the heel block, and unglued the fretboard extension. All went well here, although I'm left with a situation whe…

Hello Friends, I've had a vintage Epiphone acoustic stored at the shop for almost two years and it's about time to wrap it up. That never happens, LOL. It has a few loose braces, which is a repair I've done in the past. The problem with this one is that no matter how I jack up the loose braces from the inside, some parts of some braces simply do not move enough to come in contact with the soundboard. This is happening in a couple…

I watched the Guild F-20 video (https://dev2.loothgroup.com/groups/repair-and-restoration/forum/topic/cracker-x-braces-on-guild-f20/#post-60310) with great interest since I've been working on a Gibson L-3 with a similar problem. A little back story - The original repair request was to address a small pickguard crack on the sound hole side. After peeking inside, I saw 5 loose brace ends on the treble side. Still a pretty standard repair…

Hi Folks. I have a new Gibson L-00 retro on the bench. It came in because the saddle had pulled forward and was extremely loose in the slot. the saddle was a narrow affair measuring out at 3/32. It had buzzing issues as well because saddle was low and neck angle is actually high (straight edge is 5/32 above bridge). Previous looth tried to correct by shimming saddle but recommended me for bridge work. I re-slotted the saddle slot wi…

I'm nearing the end of my first build. I have about 1 mm gap above the top at the end of the fingerboard extension. I've read and seen some guidance to clamp that down while gluing the extension. Others seem to build in a wedge-shaped shim - although it seems that is mostly done with neck resets and not new builds. A straight edge on the frets is just slightly above the top of the bridge so I think my neck angle is good. What are your t…

Hello -- I am trying to joint a Tele-style mahogany neck blank. I have a Metabo planer in good condition, but no jointer. I secured the c. 40 mm thick blank to a flat plywood sled and shimmed it well. It's hot-glued in place, and absolutely no rocking from any corner or edge. But as I plane it down, I still have about 1 mm difference from one end of the blank to the other when I put a straightedge on the surface (see photo, with backlig…

First time here on the forums, not sure how often I'll check in, but thought this the best place to post it. Was playing with an idea proposed by Buck Van Laarhoven on a parametric model for bolt-on neck shims, and found the formulas I wrote up translated easily to Taylor and conventional acoustic neck joints so decided to add boxes for those as well. I'm not well versed in Google Sheets, but couldn't see a way to upload the file direct…