The Hub

Looking to get a custom fingerboard slotted, radiused and cut for block inlays, preferably in Canada. Any leads much appreciated! 🙏

Howdy folks, I'm a 2026 graduate of the two year guitar program at Red Wing (Minnesota State College Southeast). Between my two years at Red Wing I worked at Collings Guitars in Austin, TX for two years in the acoustic neck department, shaping and finish sanding ~2000 necks, radiusing and gluing ~750 fingerboards, and pressing ~100 sets of frets. I also spent a couple months in the finishing department level sanding and pore filling ~300…

I am repairing a damaged Stella parlor guitar. The original top was birch, plain sawn at 0.100 inches thick, ladder braced with multiple beefy braces and irreparably split, warped and generally separated from the sides. I want to keep the instrument ladder braced with a movable bridge and upgraded tailpiece, all firsts for me. I would be grateful for input on 2 issues. 1. The new top is Adirondack spruce that I’ve reduced to about 0.110…

Let me start with this; I'm trying to find the root cause of difficult fret wire installation of two different SM fret wires. I've spent a lot of time gathering dimensions and experimenting with techniques wich could cause the problem. I enlisted the help of a colleague who arrived at a similar poor performance. His solution was to glue the fret ends/ beat the frets in. My "rather" is to find the root cause so I don't have to go thr…

Hi there! Working on a Squire Vintage Modified Jag. relevelled and crowned the frets. Lovely job. Set the relief and action to factory spec. So far so good. With a capo on the first fret, I set the string radius at the saddles to 9.5" using an under-string radius gauge, everything lined up nicely... ...but when I measured the action of all the strings along the 14th fret using my digital nut slotting gauge (expecting a unifo…

Hi all, new to nut slot work world, please can you help me with this mystery? fret levelling, neck relief and string action adjustment all completed to Fender 9.5" radius spec. very happy with that. the next step: 0.011” High E string’s nut slot was a bit low. I used Dave Johnson’s (MI Guitar Craft Academy) “q-tip slot raising method”: the pulled cotton strand, plus extra thin CA glue, to fill the slot, then trim it off once dry,…

Doug Proper designed a sanding jig that supports variable concave and convex curves, described in the following Loothgroup article: https://loothgroup.com/post-imgcap/the-variable-radius-sander/ I built one and am impressed with how it facilitates preparing bridges, braces and also allows tracing any radius using the chord formula. I made a rough measured drawing and assembly guide to share, with Doug's blessing. First step, ma…

I have a set of bubinga for an acoustic back, but one piece had a slight cup that made it difficult to work with for joining together. This is pre-thicknessed, with the piece at 4.5 mm thick. I tried wetting and heating it, as I do for sides, and pressed it flat during the process. I heated it to 300 degrees F, and then let it cool while pressed, and the cup got substantially worse. I then pressed it into a reverse cup using a radius…

Hello, One of my commissions is coming down the pike and it's going to be my first time using bar frets. I could use a once over for any helpful tips if you have any. About the guitar: Aged HD-28 but mahogany back and sides. I think Martin called this a HD-28 M? Skipping the truss-rod and using two carbon fiber strips. My process for Frets: 1: I CNC my fingerboards to a 16" radius and for T-frets I use a .023" to cut slots with a mat…

I cut the fret slots for a baritone guitar build today, so I thought I'd share my method for cutting fret slots, as I think it is a bit unusual. I radius and profile my fretboard before I cut the slots. I print out a paper layout of the fretboard, double-stick tape it to the radiused and profiled fretboard, line up the saw by eye to using red hatch marks on the printout, and saw the fret slots with a 3" circular saw that rides on…