The Hub

I need some suggestions from the many great repair senseis out there.The customer is fine with a structural repair and not concerned about making it invisible. I told him you will see anything I do. He was fine with that and has a budget of between $700-1000. It's a clean break. nothing missing, It closes tightly.. I was thinking either 1) the generic double splines one on either side of truss rod and touchup as best I can. Or 2) the ab…

I had a customer ask me to take a look at this electric guitar an "amp guy" did some work on. (if you couldn't tell by the size of cap he installed 😆) Seymour Duncan hsh pickup configuration. Is there any good or logical reason one would put the north start, finish and the south finish all on the same lug of a switch? The guitar plays but has more buzz on the hb settings than the single coil. I know how to rewire it to be more... traditi…

At what point do you tell a customer that their acoustic instrument needs a bridge reglue? Do you do it when the corners are just barely starting to lift? Once it has begun to affect playability/tuning stability? Do you offer half-measures to save them money when the damage is not too bad (dripping in some thinned tite bond instead of removing the bridge entirely for example)? I ask this because a Godin acoustic bass just came across my…

I've owned this Jersey City made 12-string/drone 'harp' guitar for a few years and want to get on the repair. I've taken the necks off many dozens of Schmidt-made guitars but never one with two necks. I've searched the web looking for harp guitar neck removal and didn't find anything of use. Asking for any tips/aids/experience from the loothers. My plan is to make a custom neck removal jig that fits the necks, and then drill the typical…

Hello! Im working on a repair for a cutsom build for a customer. Its a Dunable Yeti built in 2022. Anyway, all work was going fine till testing the rod... i discovered that the rod is working the opposite of how it should function on any other guitar. CCW is tightening (and no, no a dual action rod) Tightening this rod is adding relief. The guitar already had too much when disengaged. Trying to figure out how to approach this as this is a f…

Long story short, customer want to add carbon fiber in the neck for strength. Without string tension, the neck is dead straight; with strings, it's about double the relief he'd like. Is it insane to add carbon to this guitar? Or is it fine?

Question about splines: At what point are they necessary? My question is primarily regarding the crack to the left between the bridge and the sound hole as well as the crack at the upper bout that runs along the fingerboard extension. I have already glued them both and used the TJ cleats that run the full length of the cracks. I have already splined the lower bout crack that runs from the bridge to the binding as it was super gappy and d…

A customer brought in a Gibson ivory top A3 mandolin. It's in good shape and has all the parts. He found it at the local thrift store here in Bishop. He wants it mechanically sound. Here are the problems: 1) Everything that comes into the shop has a shrinkage component and the effects of course very from instrument to instrument. This instrument is no exception and the results of that shrinkage, in this case, are severe. The top, ba…

Thought fellow looths might enjoy this geekery. I've often wished for custom size heating blankets, but didn't even try uploading the file to get a quote from some of the major manufacturers. I was looking to spend countless hours of my life on something and save a hundred bucks. So I did some research, a little bit of head scratching, a slight bit of math reckoning, and made this '70s Martin bridge plate remover. Pretty slick, nice…

Hey, I'm working on a 2017-ish Taylor GS Mini which has a delaminating headstock...see photos... I was surprised to see that the laminate was plastic... I reckon quite a few of the community will have done this job many times, so I'm after group wisdom :). Just a small request I know... Just Fyi...I haven't quoted the customer yet, but I reckon (with some other work I'm doing on the instrument)...our budget will be limited.…

I have a Favilla Classical guitar on the bench, in for a bridge reglue. This is a low to mid-range classical guitar, made circa 1960, and it's an heirloom guitar for the customer, he basically wants it back in playing shape. The story is that he went away on vacation, and when he returned the bridge had delaminated from the top and took a fair amount of finish with it. It also appears that someone attempted to glob on superglue at some…

Gah! I need help wiring Lollar Monoliths to coil split each pup at their own 2 way mini switch...client brought it in wired to a card ( based on rough drawing ) said he "tested it"....I had to clean up his wiring and soldering some...both pots, 3-way and 2-way switches are functioning but I get a weak signal when plugged in....what am I missing here? I redrew it ( nicer drawing ) with the black hots going to the 3-way ( swapped with gre…

Well, I have exhausted all the internet can offer for options for a replacement bridge. The customer, long ago, removed a ton of material from the bottom(!!!!) of the bridge, and now that ive taken this guitar on as a restoration, its up to me to make a new bridge. I have found some ultra small pattern bits, and round-over bits to do the inside of the mustache flush, but I can not for the life of me decided how im going to cut the bulk…

A new one for me... joint is pretty much centered between 12th and 13th.

Hello again folks, how is everyone! So I'm curious about what people here think about re-tops, who's done them, and what sorta ballpark rates you've charged for past completed jobs. I've got a bit of a wild one here, so strap in if you've got a couple minutes for story time! Back in 2012, I traded an HD28V of mine for a cool 1966 D-35 that needed some work. Basically, the body and neck of the guitar were fine apart from…