The Hub

It would be helpful what this group is doing regarding fret glues, no glue, wicked-in thin CA, slot fill medium CA +/- acceleration, aliphatic? What do folks like/dislike and why? Do you practice differently bound vs unbound? How do you minimize cleanup after thin CA? Does it matter acoustically if the frets are glued? It adds time and the risk of a CA mess to the job … Thanks

Greetings and thanks in advance for your help. I live in one of the most inhospitable places in the world for wood storage (Mojave Desert CA) and later this year will be moving to another more inhospitable place (Sonoran Desert, Buckeye AZ). The realative humidity is currently 16% and that will drop when summer comes. I'm attempting to collect and store wood for future builds and today I spent some time wrapping all of it in seran…

Hi all, new to nut slot work world, please can you help me with this mystery? fret levelling, neck relief and string action adjustment all completed to Fender 9.5" radius spec. very happy with that. the next step: 0.011” High E string’s nut slot was a bit low. I used Dave Johnson’s (MI Guitar Craft Academy) “q-tip slot raising method”: the pulled cotton strand, plus extra thin CA glue, to fill the slot, then trim it off once dry,…

Hi, thanks for this great resource. This is my first post here. I work on my own instruments and have little experience with advanced repairs. Recently I acquired a ca. 78 Sigma DR28H. I bought it because it sounded great and came with a pickup installed. I wanted something for open mics and gigging. With light strumming it sounded fine but I found some buzzing when I took it to a jam. I made a nut and saddle , adjusted the truss…

I have repaired numerous top crack on this instrument built by a customer at a guitar building camp. The bridge was off and warped. That has been addressed. After gluing with hide glue and splining the crack these top two did not closed as much as I would have liked. The bigger is about 1/32 at the widest and the other about 1/64. The crack is tight at the bottom. If I can help it I would like to fill it rather than spline it as I have…

Need some guidance for binding repairs. I'm using the "Martin method" using CA glue and tape for re-attaching the binding. From there: Scrape glue 400 grit to level Brushing on Lacquer 400 grit to level Meguiars #1 Meguiars #3 Meguiars #7 All by hand. But I recently purchased a Proxxon hand polisher. I'm still getting big marks. Its usually "ok", but I'm noticing huge swirls. Not pro. I do not have the money/space for…

I’ve had success placing Titebond under top braces using an artificial insemination catheter (not the AI you thought!) The catheter is PVC, 11 inches long, has a standard Luer hub for syringes and is thermoplastic so it’s shapeable. Purchased on Amazon Weewooday 50 Pcs Disposable Artificial Insemination Rods Disposable Breeding Rod Tube Flexible Breeding Catheter Tube for Dog Goat Sheep(10.8 Inches,White) URL = https: //a.co/d/03SDiw…

Hey, I've just had a go at repairing a cracked Epiphone Hummingbird and it all went well except burning through the colour of the finish when sanding it up to a gloss. Any ideas for patching this up?

So I’ve finally gotten around to hammering a couple frets in after sawing the slot. There is the tiniest gap between the fret and fingerboard is this normal or did I not saw enough. I think you would like the fret to be completely flush right? You can barely fit a piece of paper under there. How much leeway is there to this? Also I will be using CA glue.

Okay gang I have a doozy of a crack repair. Young guy brought in a Epiphone LP Limited Ed. He had picked up the case while it was unlatched at the guitar took a nasty tumble. Severe finish damage, and the wood has a shear split in it as well. The undercoat is thick with a thin layer of nitro color on top. Spoke with a sweetwater rep and they said that the finish was nitro. Here's the guitar specs via Zsounds: Epiphone Inspired by Gibson…

I had a wild idea, and I would love to be talked off the ledge before I try it. I've seen some acetone vaporizers used in headlight repair, and the thought occurred to me that the concept could possibly work for blending poly finish with Ca (fill and finish) to lessen witness lines without sanding. The idea would be to fill the finish chips as usual and scrape flush with a razor blade, then use the vaporizer to blend the edges before…

This is just a rant against the Stew-mac touchup pens. Ive just never had them functionally work, without creating more of an issue than there was in the first place. Through an "act of god" I chipped a small bit of freshly buffed and polished laquer off the headstock of a Taylor that I refinished. The guitar had that nasty bubbling around the tuners and CA glue didn't fix the issue, so I stripped the front of the headstock and airbrush…