I’ve got a client requesting a weight reduction on his Kurt Cobain Jaguar My approach would be in 3 steps see how much I can route down the existing cavities (might not be a lot of weight loss) route under the pickguard without compromising the instruments integrity if additional weight loss is required, drill into the body with airline drill bits to gain a few more grams current total weight all including 4.2kg Any advice is welcomed 🙏🙏🙏
Sounds good. If it works for you we can meet up in a Loothalong breakout room and work through it together. This might be a fun demo to do in the 3d club think tank if all works as intended. Jamie
I was approached by a local music venue about finishing over the signatures on this Dean guitar. I have finished over signatures before, but never an entire guitar. The main challenges, as I see it, with this endeavor is prepping the existing finish. Cleaning the existing finish without disturbing the signatures will be time consuming enough, but abraiding/sanding the finish will be cost prohibitive. I have already experimented on a test…
Guitar fell straight down on the headstock when it was hanging up at the refinishers. Shit really does happen! Grain is pretty much shattered around the adjustment nut. Thinking I’ll replace the entire broken area with a completely new piece of mahogany. Scarf it in between the volute and 3rd fret. Probably even a 3 piece lamination to mimic the neck. This one was not the clients fault so the expectations for looking close to original a…
In the past I’ve accomplished this using a large japanese saw and an angled jig for the majority of the cut, and then smaller japanese saws and chisels for interior of the cut. Sandpaper pulls for ref…
Any tips on handling the off-gassing for vintage guitars? I just took in a 1941 D'Angelico. The original tortoise shell pickguard is gone and has been replaced. New case as well. The frets up the neck are going to need to be cleaned. But are there any other precautions I should tell the client to take? Anything I should take into account? -Mike
Gibson Roy Smeck Radio Grande 7 string! in for tuner replacements... Currently has faulty original grovers, wants waverly titanium that I'd have to modify the plate shape to fit---and drill a new lower hole mount to avoid new holes drilled in the headstock ( around the "e" in waverly logo; and new plate hole and old plate hole would intersect by a whisper ). I'd have to remove the cog to mill & install, but the mounting screw head has c…
I know you're looking for the best ways of utilizing the Waverly tuners, but perhaps using tuning machines that are a better fit (maybe without drilling new holes) would be a better solution.
I've got a client with a '72 Tele. It needs a re-fret, but the truss rod isn't functioning. In fact it's backed out of the channel significantly, and there's a bulge in the neck underneath the first fret which suggests to me there's something going on with the truss rod anchor. The puzzling thing is the wood in the neck has bulged, but the skunk stripe and the finish don't appear to be disturbed at all. I'm thinking I'll probably hav…
The only other potential thought I have outside of maestro's James and Ian is, while it's hard to know via photos; has the neck been refinished? I'm seeing some sheen in the worn areas which I wouldn…
Hello! A client of mine have given up on the idea that he'll make good use of this Gibson and Fender stash. He willing to entertain separating items and is open to offers. No idea how to value this lot... Please call or text 1-765-729-5282 if you have questions or offers. Located in between Indianapolis and Fort Wayne Indiana. As I understand it, getting NOS Gibson headstock veneers can cost and arm and a leg these days... The headstock ve…
Hi all,
I am a newer guitar tech and after dozens of repairs this particular Simon & Patrick Luthier Cedar top SP6 acoustic dreadnought from the 90-ies with a bolt-on maple neck has been an incredible challenge.
It came with a maxed out and stuck truss rod with a considerable up bow in the neck, extremely low saddle with barely any string break angle, so it needed a neck reset. Later on I figured out that it also has a pretty dras…
Gah! I need help wiring Lollar Monoliths to coil split each pup at their own 2 way mini switch...client brought it in wired to a card ( based on rough drawing ) said he "tested it"....I had to clean up his wiring and soldering some...both pots, 3-way and 2-way switches are functioning but I get a weak signal when plugged in....what am I missing here? I redrew it ( nicer drawing ) with the black hots going to the 3-way ( swapped with gre…
I'm not seeing an actual ground going to the black leads for the pickups (unless there is an internal connection at the pickup). Try putting a jumper from the ground to the black lead at the switch.
I have a "fender", which I believe is a knock off, in my shop. I didn't immediately catch that it was a fake, but as I worked on it it's become fairly undeniable, in my opinion.
For the neck — the fretboard is made from two pieces of rosewood, the headstock decal doesn't look right, the truss rod is metric, the tuners don't look like a MIA Fender, and there's no walnut plug on the truss access. The model name being wrong is suspicio…
My opinion is to avoid mission creep. Repairing instruments and authenticating instruments are two different jobs. Only one of these jobs are you actually being paid for. I've never experienced any up…
Hello again folks, how is everyone!
So I'm curious about what people here think about re-tops, who's done them, and what sorta ballpark rates you've charged for past completed jobs.
I've got a bit of a wild one here, so strap in if you've got a couple minutes for story time!
Back in 2012, I traded an HD28V of mine for a cool 1966 D-35 that needed some work. Basically, the body and neck of the guitar were fine apart from…
Oh yes, it is absolutely not down to financial matters here, or I'd have abandoned it completely hahaha, I've been thinking more about it, perhaps I will take the plunge, and have a bit of silly fun w…
Hey all.
I apologize if this type of post isn't allowed here but wanted to share anyway.
I've been building a tool called Looth specifically for luthiers and repair techs, and I'm looking for a small group of interested looths to help shape it a bit more before it goes public.
I got tired of managing spreadsheets and decided that it could be simpler and more automated.
The core idea is simple: one place to track every build…
(Just to set expectations, I bought this for the sole purpose of learning. Not a client project) I got this Martin D28-12 in destroyed condition, after an airline did something awful. As I see it: - Top cracks - Back cracks - Top & side separation with some broken off kerfing - Brace ejected When I was looking at the pictures online pre-purchase, I thought I might take the neck off and re-top it, or at the very least, take the top off and fix…
