The Hub

I've owned this Jersey City made 12-string/drone 'harp' guitar for a few years and want to get on the repair. I've taken the necks off many dozens of Schmidt-made guitars but never one with two necks. I've searched the web looking for harp guitar neck removal and didn't find anything of use. Asking for any tips/aids/experience from the loothers. My plan is to make a custom neck removal jig that fits the necks, and then drill the typical…

Good morning everyone, I was taking some measurement on production necks with scarf-joint (13° headstock angle) to add some machining process with the cnc. I so recreated the standard neck blank feature (100mm wide and 20mm thick), then drawed the 13° angle. Everything correspond the to the real piace but two measurement: the startingcut behind the break angle is ''off'' by 20mm +/- as well as the cut on the bottom, still off by 20mm…

Hi all, I am a newer guitar tech and after dozens of repairs this particular Simon & Patrick Luthier Cedar top SP6 acoustic dreadnought from the 90-ies with a bolt-on maple neck has been an incredible challenge. It came with a maxed out and stuck truss rod with a considerable up bow in the neck, extremely low saddle with barely any string break angle, so it needed a neck reset. Later on I figured out that it also has a pretty dras…

Hi everyone, Every once in a while, I come across a bass that simply refuses to stop buzzing. Right now, I’m working on a bass (I won't name the brand, but it’s in the €2,500 range) that has a slight fretboard hump near the neck pocket. I figured that was the culprit, so I performed a fret level under string tension. The frets are now perfectly level... yet, it continues to buzz across the entire fretboard, even with fairly high a…

Is anyone using the LuthierTool Neck Angle Jig. I have a quick question about setting up to cut the tenon and getting the correct angle dialed in for cutting the heel block. TIA for any help

I have a 74' D-28 im working on, just curious what you guys do in terms of process steps. Right now, im setting the angle, without frets(I reinforced the square tube rod with carbon fiber and will need to refret once put back together.) Do you guys shoot for the straight edge hitting the top of the bridge with, or without frets? Im wondering if I should undershoot my bridge just a touch so that then I can fret and have a good saddle hei…

I added measurements for the Yamaha FG red label FG 75's some time ago. I Keep getting these in for neck resets. I wanted to add photo's from the first one because they show that the dovetail joint does not align with the first fret beyond the neck/side to make folks aware so that one knows to slightly angle the drill to hit the pocket. I do the same on the holes drilled at the fret at the side/neck fret. I slightly angle the drill…

A Gagliano Jumbo probably made by Kay in the 1950's. It looks like this had a previous neck reset based on the shims and some sloppy chisel work. I removed the 14th and 15th frets because I had read that these might have a straight tenon. I didn't need to drill any holes for heat, as the spruce shims both split in half after the fretboard extension was released. The dovetail is about 11mm long, the pocket is 14mm deep, and the 15th fret…

can anyone help me determine the neck angle on a 12 fret to the body neck Robbie Obrien says the gap betwwen the plane of a 14fret neck and the top of the soundboard at the bridge should be3.5 mm. does that hold true for 12 fret necks

Before I hack into the Yamaha, I would like to get the opinion of the experts on a method of steaming the upper end of the guitar and ‘pressing’ the neck down to adjust the angle back to factory. There are several you-tubers that have tried and recommend it. My novice intuition is that even though it may work, wont the steaming of other areas of the body such as upper braces, etc, end up weakening the construction (glue stability) to…

Hello friends - I am a bass guitar builder who is considering building a neck-through Flying V-style guitar with a 25.5" scale length and a Floyd Rose tremolo bridge. I have not built any neck-through instruments and would appreciate any guidance on where to begin with respect to laying out the design, in particular, getting the neck angle right and the headstock angled properly. Any resources are welcomed and if someone has any interes…

Hey all, I’m curious to know people’s general thoughts on the appropriate or ideal saddle height after a reset. And, when to replace a bridge that’s been shaved down. I know there are a lot of factors (for me anyhow) and this question could open a whole can of worms when it comes to the specifics of the guitar, its age, style of bridge and desired sound. I’m providing an example I encountered recently, but would also like to know people…