The Hub

Hi all, I'd like to get some input on how to address this top blowout. For starters I own this, I got it as a project guitar, 71 D28. I'm not as experienced with acoustics as electrics and this is a big project but I got it to learn new skills and I'm confident I can do it with guidance. It had been stored in the case for many years under tension and was way too humidified. The bridge had pulled up I assume in stages. The center seam se…

good evening to all. This one showed up on the marketplace. I'm wondering if its too much to chew for me at this time. Is it a very difficult repair? Is it worthwhile pursuing? It's another $25 crash test dummy. Please, don't hold back. I can take it.

I've owned this Jersey City made 12-string/drone 'harp' guitar for a few years and want to get on the repair. I've taken the necks off many dozens of Schmidt-made guitars but never one with two necks. I've searched the web looking for harp guitar neck removal and didn't find anything of use. Asking for any tips/aids/experience from the loothers. My plan is to make a custom neck removal jig that fits the necks, and then drill the typical…

Howdy folks, I'm a 2026 graduate of the two year guitar program at Red Wing (Minnesota State College Southeast). Between my two years at Red Wing I worked at Collings Guitars in Austin, TX for two years in the acoustic neck department, shaping and finish sanding ~2000 necks, radiusing and gluing ~750 fingerboards, and pressing ~100 sets of frets. I also spent a couple months in the finishing department level sanding and pore filling ~300…

Question about splines: At what point are they necessary? My question is primarily regarding the crack to the left between the bridge and the sound hole as well as the crack at the upper bout that runs along the fingerboard extension. I have already glued them both and used the TJ cleats that run the full length of the cracks. I have already splined the lower bout crack that runs from the bridge to the binding as it was super gappy and d…

Hi all, I am a newer guitar tech and after dozens of repairs this particular Simon & Patrick Luthier Cedar top SP6 acoustic dreadnought from the 90-ies with a bolt-on maple neck has been an incredible challenge. It came with a maxed out and stuck truss rod with a considerable up bow in the neck, extremely low saddle with barely any string break angle, so it needed a neck reset. Later on I figured out that it also has a pretty dras…

Hi Folks Newbie here so please bear with me. I have a lovely early 90's Yamaha LD-10E acoustic in for repair, I think all solid wood? made in Indonesia and a lovely sounding instrument, however the electrics are letting it down. The pre-amp has a PCB populated with SMD electrolytic caps. Many of these have leaked and destroyed the PCB pads underneath. Repairing the traces is nigh on impossible so it looks like I'll have to replace t…

Hello again folks, how is everyone! So I'm curious about what people here think about re-tops, who's done them, and what sorta ballpark rates you've charged for past completed jobs. I've got a bit of a wild one here, so strap in if you've got a couple minutes for story time! Back in 2012, I traded an HD28V of mine for a cool 1966 D-35 that needed some work. Basically, the body and neck of the guitar were fine apart from…

Here's yet another acoustic guitar bridge tear off, this time the sound board came with and was damaged. The bridge is not damaged and can be cleaned up. But how would one go about repairing the sound board where the pegs? this is another skill building exercise - not a customers guitar. I included pictures of the bridge plate. If this has already been covered here, please provide a link. Thanks again very much to this great group…

I have a Taylor Acoustic in for a setup and I had a couple of questions: 1. My main one is how you would go about gluing the label back on? I'm probably overthinking it but I'm curious if there's a universally recognized way of doing this? 2. I have some very minor finish damage which I'm not planning on touching, but I am curious how one would go about repairing it. Would this be a case of drop filling lacquer? What would be the…

Hi all, I'm new here. I've been playing guitars for ~15 years and recently started as a technician at a music production school in London, where part of my job is maintaining the guitars. I picked up this 50s parlor nylon the other day and it's in bad shape but I don't know how to go about repairing it. The main issue is the bridge. The guitar was kept high strung and the bridge has twisted and lifted off slightly at the base. T…

Has anyone removed the stabilizer bar from a Fender Wildwood Acoustic guitar? I need to repair the bridge area and I cannot figure out how to remove the internal stabilizer bar. Any input would be appreciated

Hi all. Brand new member. I’ve been building a classical guitar via kit from LMI for a couple of years now. I keep putting it off but recently became motivated to get back to it. Unfortunately LMI is out of business so I now have no one to go to to ask questions. I’m at the stage where I’m putting the sides together in the form. I followed the dimensions for the form based on the plans as I measured them, but the sides overlap pretty ba…

Hey lads I'm in a bit of an indecisive spot with a 70's yamaha acoustic refret. Pulled the original frets and the tang is .018" with no barbs just divots pressed into the lower edge. The slot is measuring .018". Struggled to find any suitable sized fretwire in stock in the UK that match what the customer wants that'll fit in the slot. Sintoms looked ideal but couldn't find any, so went with something with 0.20 tang and they're not pressi…